Carbon steel pump equipment parts repair methods

Chemical pump parts used in a wide range of steel materials, the welding of a great difference. In the case of carbon steel, the higher the carbon content in the steel, the greater the propensity for cracks to occur during welding and the poorer the weldability. The more stringent the requirements are for welding technology.
1 low carbon steel parts welding
w (C) ≤0.25% carbon steel is mild steel, good weldability. Bonding welding generally do not need to take special technological measures, the choice of general J422-type electrode can be satisfied with the results. Only in special cases, for example, parts stiffness is very large, when the weld is very large or low temperature welding cracks may occur, pay attention to the selection of high quality welding rod, in order to enhance the crack resistance of weld metal, while using a reasonable The welding process to reduce welding stress.
2, high carbon steel parts repair welding
Carbon steel having w (C) of 0.25% to 0.50% is medium-carbon steel, and w (C) of high-carbon steel is not less than 0.50%. With the increase of carbon in steel, the sensitivity of welded joints to cracks increases accordingly. The cracks are mainly caused by the hot cracks in the weld, the cold cracks caused by the low-plasticity and hard-tissue caused by the rapid cooling in the heat-affected zone, and the hydrogen induced cracks mainly caused by the infiltration of hydrogen at the root of the weld.
In order to prevent cracks in medium and high carbon steel parts welding process can take the following measures:
1) to improve the welding heat cycle, reducing the cooling rate of the main measures for the preheating before welding. It can reduce the hardness of the heat affected zone, and reduce residual stress and deformation, thus effectively preventing cracks in the weld and heat affected zone.
The degree of carbon steel preheating depends on the amount of carbon content and part stiffness, you can roughly the following empirical formula to estimate the pre-heated electrode arc welding temperature:
Preheat temperature (° C) = 500 (CE-0.11) + 0.4t (5-1)
Where CE --- carbon equivalent of steel (%) ,: CE = c + (Mn + si) / 4
t-- part thickness (mm).
This formula is mainly used for parts thickness t ≥ 20mm) situation. Second, multi-layer welding can also be used to improve thermal cycling. Each seam on the weld after a preheating can play a role, but also on the role of a slow cooling before the weld, which played a good role in preventing cracks. Post-welding slow cooling and stress relief treatment play a good role in the crack.
2) Select the appropriate electrode as far as possible the selection of low hydrogen electrode to enhance the crack resistance of the weld, the electrode should be dried and placed in the insulation tube, with the use of take. The intensity of the electrode should be consistent with the base metal.
3) to strengthen the cleaning work of the welding area completely eliminate any possible source of hydrogen into the weld, such as oil, water, rust and other impurities.
4) Try to reduce the proportion of base metal into the weld, such as open V-shaped groove, the first layer of welding with a small current welding, etc. are all effective methods. However, care must be taken to melt the parent metal to avoid defects such as slag inclusions and incomplete penetration.

Silicone Sleeves/holders

Introduction of Silicone sleeves/holders:


In our daily life,silicone sleeves/holders are widely used here and there ,they are our life's good partner,bottles need sleeves to carry easier ,cups need them to do insulation,electonic lines need them to be insulator,they can also decorate products more beautiful and colorful as gifts,etc!



What we can do on Silicone sleeves/holders?

As an OEM&OEM manufacturer ,OK Silicne Gift Company has one-stop service for our customers ,we can help them to do Silicone bottle sleeves,Silicone Cup Sleeve,Silicone Sanitizer Sleeve,silicone bottle holder ,silicone camera holder,silicone speaker holder,powerbank holder!


Here are some Silicone sleeves/holders photos for your ref.

Silicone bottle sleeves

Silicone Cup Sleeve

Silicone Bottle Sleeves,Silicone Cup Sleeve,Silicone Bottle Holder,Silicone Camera Holder,Silicone Speaker Holder,Powerbank Holder

Dongguan OK Silicone Gift Co., Ltd. , https://www.dgsiliconewearablegifts.com