♦ Integration of dehumidification, drying and conveying functions;
♦ Dehumidification, drying and conveying integrated unit are equipped with honeycomb rotor for getting low dew-point dry air with good stability. Cut-off valve in semi-open and fully-enclosed feed system are equipped to assure no remnants materials left in material pipe.;
♦ Equipped with micro computer and photosensor hopper for optical machine for micro powder cleaning, avoiding spot in optical products.;
♦ Stainless steel mirror polishing of all material contact surface and closed loop feeding system to avoid the material get contaminate or damp;
♦ High-performance filter to filter dusts down to 0.3um and the filtration rate can reach 99.995%;
♦ Bottom blowpipe design of material barrel with cyclone exhaust device for thermal drying barrel, to keep temperature and improvedrying efficiency;
♦ Double cooler structure to assure lower return air and dew-point.
Â
Â
The main body of honeycomb rotor is formed by ceramic honeycomb which is made from ceramic
fiber and organic addictive. Molecular sieve and silicone as basic material are crystallized and sintered
at high temperature for hard surface and tightly attached to the internal wall of honeycomb. Therefore,
it would not generate silt as barrel packaged or turntable molecular sieve to contaminate the plastic.
The honeycomb rotor can be used permanently and can be washed, while the ordinary molecular sieve
must be usually replaced for its easily getting saturate and aging. The water of moisture return air will be
quickly absorbed by molecular sieve when it across innumerable ostioles of the honeycomb rotor,
Therefore ,the air is completely dehumidified and reaches a very low dew-point. Regenerating and
dehumidifying happen simultaneously and follow the similar principle, except that their regeneration
air flows in the opposite direction.
Dehumidification and drying: The hot and humid air from drying material barrel is blown into honeycomb rotor
after cooling. The water in air is absorbed by rotor and then desorbed by the regeneration heating air. The two
airflows workon the rotor at the same time, and as the rotor rotates, the water in air can be absorbed and desorbed continuously. Thus,a stable low dew-point air is formed and then blown into the drying barrel after heated to the
drying temperature of plastic, forming a closed loop to dry material.
Material suction: material suction is to suck material from material barrel or other material container into drying
material barrel. The motor starts to run when the magnetic reed switch of the vacuum hopper detects no material,
generatingvacuum in vacuum hopper, and then the material in material barrel will be sucked into vacuum hopper
because of the pressure difference of air. The motor stops working after sucking and the material will drop into
drying barrel. At last the dried material will be sucked into SVH hopper or other hopper which is set in plastic
moulding machine.
TECHNICAL SUPPORT
      XINGKE has two major production in abroad and China, with a lot of agents , representative offices and four branch in over the world ,set up the leading visualize in molding manufacturing processing
WHY US ?
*Â More than 30 years experience in plastic moulding &Â extrusion industry;
* CE,ROTH,ISO etc. certification exams passed.
* Professional sales team for overseas markets;
* High efficiency, High communicate
PRODUCTS VIEW
* Raw Materials Processing System
* Centralized Drying Dehumidifying System
*Â One-Stop Solution
* "Euro" Slow-Speed Granulators
*Â Gravimetric Blenders
*Â "Euro" Hopper Dryers
*Â All In One Dehumidifier Dryers
*Â Honeycomb Dehumidifiers
*Â Oil Heaters
* Water Cooled Chillers
FAQ
1) Are you manufacturers or trading company ?
X: Manufacturer.We produce machines in China factory and developing products from South Korea for best technical resourses , It can realize to advanced technology and reasonable cost for clients.
2)Â Do you have CE,EU,ISO9001 etc. certification ?
X:Yes , All of our products approved with these certifications.
3)Â Do you have any experience in new IMM fatory planning ?
X:Yes, also we can offer you one -Â stop solution (liquid water ,eletric,vacuum ) for your IMM or extrusion facory.Â
EXHIBITIONS
We have different Silicone Fluid, silicone oil for different industries.
dimethyl silicone oil: lubrication, shakeproof, electric insulating oil, defoamer,mould release, cosmetics.rubber and plastic, heat-conducting medium etc.
vinyl silicone oil: silicone rubber compound
hydroxy silicone oil: aids for silicone rubber, waterproof,softner and antiadhesive agent for fabric,paper and leather
amino silicone oil: fabric(terylene/polyester)softer treatment, Fabric; textile, Cosmetics, improve hair combed ,Slippery and shining .
phenyl silicone oil: Insulation, lubrication, damping, quakeproof, moistureproof, dustproof, high temperature hydraulic fluid, High temperature heat carrier, filling oil for Transformer and pressure signals transferring medium for various pressure transmitter.
hydrogen silicone oil: aids for silicone rubber, waterproof,softner and antiadhesive agent for fabric,paper and leather.
Polyether Silicone Oil: silicone surfactant, textile adjuvant,etc
The role of silicone in rubber, plastic and metal demoulding
Because of the non-stick property of dimethyl silicone oil and rubber, plastic, metal, etc., it can be used for the demoulding of polyurethane microporous elastomer molded products, but also can be used for the demoulding of peeling polyurethane molded products, rubber products, ABS molded products, etc. The main advantages of the release agent are small release force, no pollution, convenient transportation, and make the surface of the product clean, smooth, clear texture. With the rapid development of polyurethane industry, silicone oil release agent market is expanding.
Silicon Fluid, silicon oil, dimethyl silicone oil, vinyl silicone oil, hydroxy silicone oil, amino silicone oil, phenyl silicone oil, hydrogen silicone oil, Polyether Silicone Oil
Luckypower Tech , https://www.czluckypowertech.com