Vacuum sewage suction vehicles, also known as sewage suction vehicles and sewage suction vehicles, use vacuum negative pressure principle to suck feces and liquid dirt into vehicle-mounted storage containers to achieve container collection of feces, reduce secondary pollution, and equipped with vehicle-mounted cleaning devices. It is the preferred equipment to improve the level of urban and rural sanitation management and improve the working conditions of sanitation personnel.
Vacuum suction car use:
It is mainly used for sewerage, rainwater wells, inspection wells, septic tanks, and sludge, excrement in manholes or petrochemical plant effluent pools for suction, shipment, and discharge. The suction pump can be self-priming and self-discharging. The sewage suction tank can be hydraulically unloaded and the rear cover can be opened hydraulically. The suction pump has a high vacuum degree and a long suction range.
The vehicle carries out sludge and sewage inhalation operations under high vacuum conditions, paying particular attention to its operation.
Sewage suction trucks are mainly used to clean city sewers, pipeline sediments, dredging of dead mud, can also be used to clean industrial drainage pipelines, walls, etc., and can also be used for watering, transporting water and highways, and can be used for fire fighting in case of emergency. .
1. Pay attention to the quality of the plate, the vacuum sealing degree, and the poor material can easily cause problems such as deformation of the tank body.
2. The choice of vacuum kit, the pressure capacity and the perception of temperature difference. The domestic kit debuts Veyron products.
3, After the choice of lid, according to the local operating environment, temperature and other choices.
4. According to the relevant provisions of the National Development and Reform Commission on the emission of the three-country exhaust gas from the enforcement country, all the country’s vehicle parameter data have been deleted since July 1, 2008. Please pay attention to identifying the country’s three emission labels and related procedures when purchasing vehicles.
Sewage truck components: oil-water separators, water and gas separators, special vacuum suction pumps, volume pressure gauges, pipe network systems, suction ducts, gravity valves, vacuum tanks, connected devices (as feces), fully automatic protection Overflow valve, hydraulic kit.
Sewage suction truck working principle: Because the suction hose is always immersed on the liquid surface, the air in the fecal tank is sucked and becomes thinner because it cannot be supplemented, resulting in the pressure in the tank being lower than the atmospheric pressure. That is, under atmospheric pressure, the suction hose enters the tank. Or because the siphon tube is close to the bottom of the tank, when the air is continuously discharged into the manure tank, it is compressed because it has no way out. As a result, the pressure in the tank is higher than the atmospheric pressure. The manure fluid is discharged through the siphon tube and the suction hose under the action of the compressed air. Outside the tank.
(1) Maintain the proper number of revolutions of the vacuum pump:
Vacuum pump speed is too high, transfer to the heat increased; speed is too low, it will cause engine knock, the parts cited additional shocks, affect the life, the appropriate working speed, pre-adjusted hand throttle maximum adjustment position.
Pump Type 50QZXDG-45
Appropriate rotation 500-600 rev / min
(2) Turn the pot on a flat ground
Failure to turn the tank over a sloping road can result in distortion of the parts and cause failures, and may cause a roll-over accident.
(3) Open the rear door and window when turning the tank
Before turning the tank, the rear fan should be opened. Do not close the door and turn the tank. The danger of overturning due to the shifting of the center of gravity.
(4) When the clutch oil pump power take-off box and the vacuum pump take power box, the engine idles, and the clutch pedal is fully depressed, and the clutch pedal is slowly raised when the clutch is engaged.
(5) Pay special attention to the car: Take the lever control lever in the middle position.
(6) Do not use this vehicle to inhale and transport waste oil and dangerous materials.
(7) Support rods and safety stops must be used when entering the tank bottom or overhauling when the sludge tank is raised.
(8) When transporting sewage, it is necessary to use a hand-door door clamp device. Since there is no anti-wave board in the tank and the center of gravity is high, the vehicle must be driven at a medium speed and a slow speed, and no heavy-duty change or sudden braking is required.
(1) Preparation before inhalation
A. Close the back door. B. Observe whether the vacuum pump oil separator oil is correct.
(2) Operation sequence
A. Depress the clutch pedal, push the power lever control lever (2) to run the vacuum pump (3), and then slowly release the clutch pedal
B, open the alarm switch (in the cab)
C. Pull the hand throttle handle to the maximum position and observe the tachometer until it reaches 500-600 rev/min (factory adjusted).
D, the four-way valve (5) conversion handle bar placed in the suction position, and check the trachea exhaust air is correct, whether the air pump operation noise, the vacuum gauge is normal and so on.
E. Remove the suction hose from the car and put it into the sinkhole. In order to make the suction hose straight or free-form, the parking position should be fully considered.
A. More than 50mm of stones, cotton yarn, leaves and other impurities will block the straw, so do not inhale and should be removed regularly.
B. Observe the vacuum gauge reading to 65-80 kPa. Completely open the suction ball valve. The half-open condition will damage the valve core.
C. When inhaling the sludge, you should always move the pipette. When inhaling high-viscosity sludge, inadvertently inhale air and water to increase the pollution efficiency.
3, sewage discharge method:
After the separation of the mud and water, open the drain ball valve (10) to discharge the sewage and repeat the suction of the mud, and pressurize and drain quickly. The operation method is as follows:
(1) Place the four-way valve (5) shift lever in the “neutral†position, and then place the drain ball valve in the “on†position to reliably discharge gravity.
(2) When the four-way valve is switched to the discharge position, and the vacuum pump continues to work, the compressed air discharged into the tank will be quickly discharged.
(3) When the pressure is drained, the discharge ball valve should be opened before the plate-moving four-way valve (5) can be placed in the discharge position, so that the pressure inside the tank is too high, and accidents and affect the seal of the tank door are avoided.
(1) Depress the clutch, dial the pneumatic reversing valve (1) to the "open" position (liberate) or push the power-lift lever to operate the vertical rod (2) (east wind) to operate the oil pump.
(2) Open the ball valve (11) to discharge part of the sewage and reduce the pressure inside the tank to open it to the atmosphere.
(3) Loosen the tank door locking device (12), loosen the handle and safely remove the screw. ,
(4) Set the open/close lever of the manual valve (4) to “openâ€. Before opening, make sure that the pressure in the tank is equal to atmospheric pressure. If the tank door is opened under negative pressure, it will damage the tank door. Seals and cylinders.
(5) Set the manual change valve's tipping valve stem to the "up" position.
(6) Definite recovery after draining the sludge: Place the cylinder-turn cylinder lever in the “down†position, and check the following for safe descent:
A. Check the tank door flange and seal ring for dirt and brush it clean with a brush.
B. Place the tank door opening/closing bar “closed†and safely close the door leaf.
C. Insert the screw of the clamping device into the screw hole on the side of the tank and turn the handle until the door leaf is tight.
Our cork yoga wheel strengthens and massages back muscles along the spine. Yoga Wheel is often used as a back roller for back pain therapy. The massage wheel works by reducing back strain and helps realign the natural curvature of your spine during use.Yoga Cork Wheel is non-slip and sustainable and help you relieve your pain well.
Cork Yoga Wheel,Cork Wheel,Yoga Cork Wheel,Yoga Wheel
Jiangsu Real Sporting Goods Limited Company , https://www.ruiousporting.com