Credit funds of RMB 3,214,400 do not include credit fund losses caused by bankruptcy of enterprises, accounting for 51.4 of the total amount of credit funds of financial institutions, 21.4 of which have been executed, and cases that have been decided but not implemented. Start. The number of cases in which the inaugural case was not executed was 3.8 million yuan. 12.6. of the funds involved.
This is the case. The main reasons for this are the following aspects: the concept of thinking is unclear. The cadres of the party and government organs and the investigators believe that the bank is opened by the state, and the money of the bank is also the money of the state. It doesn't matter if you can't chase it back. As long as you support the local economy, you can do it. The result is that killing chickens and taking eggs is empty; it is a poor social reputation. Individual business units or residents are proud of their debts. After doing everything possible to borrow money from the silver hall, the ass took it. The bank’s existence is rather lossy, and it is not willing to issue loans, adding the wrong business idea of ​​the risk; The implementation of credit litigation cases is difficult to implement. The regional economy is seriously lagging behind and the implementation environment is poor. The financial enterprise won the lawsuit and lost the money; it was the enterprise restructuring and reform, and the subject was translocated. With the continuous deepening of the reform of the national economic system, the implementation of the policy of large-scale and one-off policy, the small and medium-sized enterprises within the jurisdiction gradually reformed and restructured, the state-owned private public private strategy was introduced one after another, and the corporate legal person was translocated. The creditor’s rights cannot be implemented.
In order to effectively preserve financial assets. Maintain the legitimate rights and interests of financial enterprises. In addition to the financial sector itself should strengthen the management of credit funds, financial enterprises urgently need judicial assistance. With the help of the party, the executives who have a promising future and have the sincerity of repayment will be presided over by the court, and the enterprise and the executor will participate in the business. Make a 1 solution. Do it right. Take the installment payment or use the debt-to-debt method to hold the case... The enforced person who refuses to perform the performance ability, while increasing the intensity, pays attention to flexible execution, for example, in the case of a trading company’s case execution, the company can be The business building performs debts to financial companies. And transfer procedures. At the same time, the building can be rented back to the original company through the form of rentback, and the financial enterprise can collect the rent to return the debt, which not only reduces the principal and interest of the non-performing loans, but also reduces the social unrest factors, strengthens the sense of purpose, and regulates the implementation procedures. . Training of executives should be strengthened to fully understand the differences between enforcement procedures and litigation procedures. Educate and guide executives to establish the idea of ​​serving the people wholeheartedly. Just to solve problems for both parties, in the process of implementation. The President and the Vice President of the Superintendent shall strictly control the matter. Prevent the occurrence of various illegal procedures, ensure that the litigation cases are terminated on time and on quality, change the past bad case of only filing a case, and implement a positive case, and compile Xiao Qing’s skills to use mass-produced CNC lathes for mass production. At present, economical CNC lathes are widely used. It is cheap. The CNC system is also relatively reliable. However, there are some common problems in mass production, which greatly affects production efficiency. In order to achieve better economic benefits, the author gradually explored some tips for using in practice. Can be better solved these practical questions, 1 tool installation. System software for economical CNC lathes usually has tool compensation. In order to facilitate the trial and determination of the relative position of the tool, after the tool compensation program is programmed, it is still required that all the tool tips on the rotary tool holder are substantially in the same position. And slightly, in the axis. In order to quickly clamp all the tools; 1; all the tools can be carried out as follows.
Enter the control system into such a program. The tool holder is retracted longitudinally. The bamboo frame is rotated through the longitudinal side of the station 1 to return the retracted long head back to the original position; the top of the claw chuck is clamped; the jog tool is placed in a positionable clamping tool by jog or manual method The location, the tool is installed as required. Align the tip with the tip of the tip. Slightly ft0.20.5mm; start the system, make the tool holder run according to the input program, and then install the first tool. All the tools can be installed one by one.
Axial positioning of the part. When processing parts in batches, the program and the origin do not have to be changed. 1 The 岑1 of the under-clamping is required to be in the same position. 1. The following method can be used to accurately achieve this; enter the taper in the spindle taper hole. The center of the taper has an adjustable screw; the workpiece is clamped to the screw each time it is clamped, so that the same kind of parts can be clamped in the same position; the length of the screw is adjusted. Can adapt to the location of the different parts.
Program to avoid losing out. We know that the torque is small when stepping electric starting. The rated torque is gradually reached after the speed is increased, if we are programming. When the stepping motor is started immediately or enters the cutting force very quickly, the motor torque may be lost due to the cutting torque of the stator. The parts that cause the machining are unqualified or scrapped, and the procedure is repeated because of the out of step. The position of the origin will also change, so that the processed batch parts will be rejected or scrapped. Therefore, the starting characteristics of the stepping motor should be considered during programming. After the stepping motor reaches the rated speed, the tool will enter the cutting state. The experience allows the tool holder to run six pieces of material without any adjustments, and then enter the cutting without any loss of step.
The program is programmed to avoid tool wear errors. we know. When the newly ground tool is just finished machining part 0, the tool wear is irregular and faster. After processing small batches of parts. It enters a steady state, so when machining parts with new tools. The machined parts should be inspected one by one. For about 45 small and medium-sized shaft parts, the tool is in a smooth state. At this time. The wear of the tool is roughly proportional to the number of parts being machined. Just edit the program. By adding the compensation amount of the tool, the quality of the parts processed in batch can be guaranteed.
When using economical CNC lathes to machine parts with high precision, the above methods can be used to ensure that the labor intensity of the workers is reduced and the production efficiency is greatly improved. He has achieved good economic benefits and has compiled several questions that need to be resolved in the practice of certified public accountants. The registered accountant of Hou Rusong is hailed as not eating the Imperial Food. With the development of the socialist market economy and the deepening of reform and opening up. The CPA profession has made great strides. Gradually entered the legalization. Standardize the track. But in the course of practicing in recent years. In the practice of certified public accountants, some unresolved questions were asked about the unreasonable structure of the CPA team. After 1999, the accounting firm was restructured. The number of certified public accountants in China is more than 30,000. There are 120,000 employees and more than 2,400 accounting firms. no doubt. This figure is incompatible with the needs of China's socialist market economy. In the ranks of certified public accountants. Some of the personnel are the WfPVuIif1WFAUp, ip.WJtfiJr, 7fiKHS6J`1klt, and some economic certifications issued by unqualified practitioners, and finally only by name. The quality of forensic is greatly reduced, and again. In the ranks of certified public accountants. Compound talents are small, single accounting type
(Finish)
Prepainted Galvalume Steel,Prepainted Galvalume Steel Sheet,Cold Rolled Prepainted Galvalume Steel,Hot Rolled Prepainted Galvalume Steel
HANNSTAR INDUSTRY , https://www.hannstarmetal.com